Chord Electronics Hugo TT 2 DAC/Preamp/Headphone Amp and Hugo M Scaler

A Great DAC Made Better

Equipment report
Categories:
Solid-state preamplifiers,
Digital-to-analog converters
Chord Electronics Hugo TT 2 DAC/Preamp/Headphone Amp and Hugo M Scaler

The DAC section of Hugo TT 2 is as flexible as the amplifier section is powerful, offering support for PCM digital audio files ranging from 44.1kHz up to 768kHz with DSD support via DoP (DSD over PCM) for DSD 64 through DSD512. As mentioned above, Hugo TT 2 uses a 10-element digital filter that provides 98,304 taps and that runs a 16FS WTA 1 filter algorithm. Moreover, the DAC section provides four user-selectable sub-filter settings: Filter 1 “Incisive Neutral” (the recommended reference setting), Filter 2 “Incisive Neutral with HF roll-off,” Filter 3 “Warm,” and Filter 4 “Warm with HF roll-off.” An IR remote control is included.

Now we come to the Hugo M Scaler, which in many ways is a ground-breaking product. Basically, the M Scaler is a very powerful digital upscaling device equipped with a >1M-tap digital audio filter—claimed by Chord Electronics to be “the most advanced in the world.” The M Scaler can accept virtually any digital audio file input regardless of resolution or sampling rate and will upscale the input data to either 705.6kHz or 768kHz levels (depending on whether the data was based on a multiple of 44.1kHz or 48kHz). But upscaling per se is only part of the story; the other part is an FPGA-based digital filter that offers a staggering 1,015,808 taps and that runs under a specialized version of the WTA algorithm—one adapted to take advantage of the enormous processing power. In the end, the M Scaler can send upscaled and pre-filtered audio data to any of the Chord Electronics DACs that support 705.6kHz and 768kHz inputs, including the Qutest, Hugo TT 2, and DAVE.

Much of the technology of the M Scaler is drawn from Chord Electronics’ previously released Blu II upscaling CD transport, with the primary difference being that the M Scaler features digital inputs only (no CD transport) and is sized and styled to conform to the Hugo TT-family design idiom. From a sonic perspective, though, the real significance of the M Scaler is that it can take garden-variety CD-quality material and upscale it to the highest practical sampling rates possible, while applying a digital filter so powerful that, says Watts, the result is sound quality equal to or better than that of ultra-high-resolution digital files. But here’s another point to ponder: The M Scaler lets its owners access the most sophisticated digital filter Chord Electronics presently knows how to make—a filter better than the ones used either in the Hugo TT 2 or in the DAVE. 

The M Scaler provides two BNC digital inputs, two optical digital inputs, and one galvanically isolated USB Type-B input. Digital outputs include one optical output, one coaxial SPDIF via a single BNC connector, and one dual BNC, which is the output of choice for best performance. While the Hugo M Scaler can conceivably be used with any DAC, the manufacturer makes it clear it is really optimized for use with Chord Electronics DACs that provide high-bandwidth dual-BNC inputs able to take full advantage of the Scaler’s capabilities. Once I heard the M Scaler in action I thought that its sonic benefits were both transformative and profound.

Using a group of very high-performance reference headphones from Final, HiFiMan, Meze, and MrSpeakers, I listened to the Hugo TT 2 both with and without the M Scaler and here is what I learned. Heard in isolation, the Hugo TT 2 sounds exactly like what it is: one of the finest headphone amp/DACs available today. While it is not quite on a par with the more than twice as expensive DAVE, the Hugo TT 2 takes worthwhile steps forward relative to its predecessor in resolution, clarity, focus, and coherency, while also offering quieter backgrounds and more dynamic muscle. In short, the Hugo TT 2 can more than hold its own in comparison to like-priced competition. However, fold the M Scaler into the equation, and the picture changes dramatically for the better.

Quite candidly, the M Scaler makes substantial, across-the-board improvements to almost every qualitative aspect of the sound—so much so that you might feel like you are either listening through an altogether different and better headphone amp/DAC, or listening to delightfully re-mastered and/or much higher-resolution versions of your favorite recordings. Once you hear the M Scaler in action, there’s no going back.

I played a Virgil Fox pipe organ performance of Bach’s Prelude and Fugue in D Minor from the Reference Recording 30th Anniversary Sampler [Reference Recordings, HDCD] through the Hugo TT 2 and, as expected, it sounded superb. But, with the M Scaler in play, the unexpected sonic improvements I heard left me slack-jawed with astonishment. First, the pipe organ’s low-frequency pedal notes sounded more deeply extended (right down to the very low-frequency shudder of air columns in the large pipes), much more tightly focused, and possessed of considerably more textural nuance. Second, the pipe organ’s middle register sounded rounder, more expressive, and more full-throated, with a more spacious and three-dimensional presentation overall. Third, the organ’s upper-register passages, which had sounded just a bit congested when played through the Hugo TT 2 alone, suddenly sounded clearer, more delicate, and far more articulate, with virtually no congestion at all. Finally, the acoustic interaction between the pipe organ and the recording space was rendered more vividly and naturally, while apparent soundstage size increased. Impressively, these improvements were wrought upon a recording widely acknowledged to be a superb one to begin with.

I enjoyed similar benefits when I played the “Triptych (Excerpt)” from A Company of Voices—Conspirare in Concert [Harmonia Mundi, 16/44.1]. This exuberant and syncopated piece for percussion ensemble and concert choir is not one that is easy for most DACs to handle, in part because of the large-scale dynamic swings involved and the perhaps slightly over-modulated choral swells that at times threaten to become ragged and strained. However, with the M Scaler assisting the Hugo TT 2, several beneficial things happened at once. First, the timing and timbres of the percussion instruments improved dramatically, with more incisive transient sounds, rounder tonalities all around, and the all-important qualities of “swing” and dynamic “jump” in evidence. Next, individual choral lines became clearer and more intelligible, while the potentially problematic vocal swells sounded better controlled and more expressive, with elements of congestion mostly (though not entirely) cleared up. Last but not least, the sounds of the concert venue were captured much more realistically (I know this because I was present in the hall on one of the evenings when the recording was made) with appropriate stage width and depth. Once again, the M Scaler/Hugo TT 2 pair made an already good recording sound not just a little but a whole lot better.

My point is the Hugo TT 2 and Hugo M Scaler fit together like a sonic hand in a glove; once you hear them together, you won’t ever want them to be apart. While the Hugo M Scaler costs nearly as much as the Hugo TT 2, it ushers in so many of the sonic extras that truly bring music to life that in my judgment it is well worth its asking price. And consider this: While Chord Electronics’ DAVE may be in a class of its own as a standalone headphone amp/DAC, the combination of the Hugo TT 2 and the Hugo M Scaler costs less than the DAVE and may actually offer better all-around performance, which is saying a mouthful.

Specs & Pricing

Chord Electronics Hugo TT 2 Headphone Amplifier/Preamp/DAC
Type: Solid-state headphone amplifier/preamp/DAC
Inputs: Two TosLink optical, two coaxial BNC, one driverless USB (16/48-capable, intended for use with tablets and smartphones), one USB Type-B, and aptX Bluetooth interface 
Outputs: Analog: stereo XLR, stereo RCA, 2x 6.35mm headphone jacks, 3.5mm headphone jack; digital: 2x DX BNC (expansion outputs)
Formats supported: PCM from 44.1kHz to 768kHz sampling rates; DSD (via DoP) from DSD64 to DSD512
Digital filters: 98,304-tap 16FS WTA 1 (Watts Transient Alignment) digital filter 
Crossfeed: Four user-selectable settings 
Operating modes: Three options are supported
Dynamic range: 127dB (A-weighted)
Noise: 4µV (A-weighted, high gain), 1.7µV (A-weighted, low gain) with no measurable noise floor modulation
Distortion: 0.00008% @ 2.5V, 300 ohms; 0.00016% @ 6W, 8 ohms
Power output (@1% THD): Unbalanced, 300 ohms: 288m, RMS, 8 ohms: 7.3W RMS; balanced, 300 ohms: 1.15W RMS, 8 ohms: 18W RMS
Dimensions: 235mm x 40.5mm x 223mm
Weight: 2.53 kg
Price: $5795


Chord Hugo M-Scaler Digital Upscaling Device
Type: Digital upscaling device with a greater than 1M-tap digital filter
Digital inputs: 2x BNC, 2x optical, galvanically isolated USB Type B
Digital outputs: Optical, SPDIF, galvanically isolated dual-BNC (which supports upscaling to 768kHz from 48kHz data)
Upscaling: 44.1kHz digital audio files (or multiples of 44.1kHz) upscaled to 705.6kHz via dual BNC outputs; 48kHz digital audio files (or multiples of 48kHz) upscaled to 768kHz via dual BMC outputs
FPGA device: Xilinx XC7A200T
Digital filters: 1,015,808-tap Watts Transient Alignment 
Dimensions: 235mm x 46mm x 236mm
Weight: 2.55 kg
Price: $4995

CHORD ELECTRONICS LTD.
The Pumphouse
Farleigh Bridge
Farleigh Lane
East Farleigh, Kent
ME16 9NB
United Kingdom
+44 (0) 1622 721444
chordelectronics.co.uk

BLUEBIRD MUSIC (N.A. DISTRIBUTOR)
bluebirdmusic.com

Featured Articles

Lists