Audio Mirror SET Monoblock Power Amplifier

The 800-Pound Gorilla of Vacuum Tubes

Equipment report
Categories:
Tubed power amplifiers
|
Products:
Audio Mirror SET
Audio Mirror SET Monoblock Power Amplifier

Extensive protection circuitry is built in. First, there’s about a one-minute delay in the application of high voltage after powering on the amp, to allow time for the filaments to warm up. The circuitry registers several fault conditions and shuts off the amp after sensing thermal runaway, arcing, excessive bias, and severe overdrive. When protection is engaged, one or two of the LEDs (one by each power tube) glows red to show which tube is the “bad actor.” The LED stays lit until the amp is powered off. The protection circuit is automatically reset once the amp is powered on again. You will note two small toggle switches located between the transformers. The one closest to the speaker terminals controls the high-voltage supply, and is intended to be used for breaking in new power tubes. Flipping this switch to the off position (toward the inside) allows the tubes to burn in just on the filament supply. After about 12 to 15 hours, the switch may be turned to the on position, and you’re good to go. The other switch, closest to the RCA input jacks is a ground lift. When this switch points outward, chassis ground is connected. Ground may be lifted in the case of ground loops by flipping the switch toward the inside.

In the context of SET amplification, the power tube is the 800-pound gorilla in the room. Its distortion spectrum pretty much dictates the sonic character of the amplifier. Let me make this perfectly clear: The 6C33C-B is no 300B. I say this without malice or prejudice. While I like the sound of both tubes, they offer distinctly different takes on musical textures. The 300B is refined and elegant sounding, while the 6C33C-B is texturally warm and tonally robust. And this suits me just fine since my first sonic priority revolves around tonal balance. My worst nightmare would be a thin and bright presentation. I generally insist on sufficient lower midrange authority to do the power range of the orchestra justice. The Audio Mirror did not disappoint in this regard. It firmly belongs to the “Tony Soprano” style of tube amplification, possessing the tonal gravitas necessary to realistically flesh out cello and upright bass. That sort of big tone is probably in part due to the inherent personality of the front-end octal tubes. This is no place for 9-pin miniatures. Oh, I should hasten to add that the 6C33C-B requires a substantial warm-up period to sound its best. These massive tubes seem to need on the order of 20 to 30 minutes to totally smooth out.

This amp didn’t sound much like a typical SET amplifier. For starters, the bass range is extended and well defined, quite a pleasant surprise. It helped that the Basszilla DIY loudspeaker pairing turned out to be a match made in heaven. In this context, the Audio Mirror sounded big and powerful, conveying a sense of ease during dynamic peaks uncommon for a typical SET. The treble range was spacious and adequately detailed to allow ride cymbal strikes to cut through the mix of a jazz quartet. Harmonic textures were pretty much in the Goldilocks zone, neither overly liquid nor threadbare, indicating a reasonably wide treble bandwidth. This is not an analytic-sounding amplifier; so don’t expect it to compensate for a fuzzy front end or preamplifier. Texturally thick tube preamps may well obscure low-level detail, so plan on coupling the Audio Mirror with a high-res preamp in order to plumb the depths of a particular recording.

Space is the final frontier when it comes to two-channel audio, so if imaging is a priority for you then you’ll definitely need to explore SET amplification. I haven’t found a push-pull amplifier that can compete in this arena against a well-designed SET. I was delighted to discover that the Audio Mirror was capable of generating a monster of a soundstage, a three-dimensional illusion with fully fleshed-out depth and width perspectives, and it did this as well as any other amp I’ve auditioned to date regardless of cost. The effect was to provide a palpable connection to the recording venue, so that with my eyes closed I could easily imagine being there.

I found myself frequently immersed in long listening sessions and came to realize that the Audio Mirror is conducive to binge listening. There’s a simple explanation for that. It delivers music’s verve with a touch of warmth and tonal gravitas that pushes all the right buttons for me. The Audio Mirror expands the reach of SET amplification to medium-sensitivity loudspeakers, and that’s a big deal for most audiophiles. It makes one helluva musical statement and would have earned an enthusiastic recommendation even with a $10k price tag. At its asking price, it represents a remarkable value and a must-audition amp.

Specs & Pricing

Power output: 45W, 4 or 8 ohms
Frequency response: 25Hz–58kHz at -3dB
SNR: >90 dB
Dimensions: 9" x 9" x 18"
Weight: 42 lbs.
Price: $4999

AUDIO MIRROR
audiomirror.com
contact@audiomirror.com

Associated Equipment
Loudspeaker: Basszilla Platinum Edition Mk2 DIY
Preamplifiers: Lamm Audio L2.1 Reference, Jeff Rowland Coherence One, Blue Velvet DIY linestage
Digital front end: Apple Mac BookPro running Sonic Studio’s Amarra Version 3.4 software, DiDit 212SE DAC, Sony XA-5400 SACD player with ModWright Truth modification
Analog front end: Kuzma Reference turntable; Kuzma Stogi Reference 313 VTA tonearm; Clearaudio da Vinci V2 phono cartridge; Sound Tradition MC-10 step-up, TPAD 1000 phonostage
Cables: Acrotec 6N, Kimber KCAG Select interconnects; Acoustic Zen Hologram II speaker cable
Accessories: Sound Application power line conditioners, Monarchy Audio AC-Regenerator

Featured Articles

Lists